| Current File : //kernel/drv/qlcnic.conf |
#
#########################################################################
#
# Copyright 2009, 2014 QLogic Corporation. All rights reserved.
#
#########################################################################
#
# Driver.conf file for QLogic 10-Gigabit Ethernet devices
#
# All the properties below can be set globally (i.e. for all instances
# of qlcnic), or on a per-instance basis. See driver.conf(4) for details
# of the syntax of global and per-instance properties.
#
# Properties specified in this file take effect when the driver is first
# loaded, typically just after system boot. Changes to the file will
# therefore not take effect until the next reboot, but will be permanent
# thereafter.
#
# If a parameter needs to be changed for a particular adapter instance,
# make a copy of the parameter. Then change the qlcnic number
# (decimal) in the parameter to match the adapter instance number
# that is displayed during the boot process.
#
# Example:
# Setting mtu Jumbo mode for adapter instance 3 only, but keeping it
# default size (1500) for other adapters.
#
# Before:
# default_mtu=1500;
#
# After:
# default_mtu=1500;
# qlcnic3-default_mtu=9000;
#
#########################################################################
#
# The property below represents the Auto tuning resource values to minimu
# m values to work within System Resource constraints. Enabling this will
# override user requested tunables rx_ring_size/jumbo_rx_ring_size to 256
# tx_ring_size/max_tx_dma_hdls to 512, max_sds_rings/max_tx_rings to 1.
# If total NIC Functions on adapter are greater than 2, then this flag
# is enabled by default otherwise it is Disabled by default.
#
# minimal_resource_mode = 1;
#
#########################################################################
#
# The properties below represents the number of receive and send descriptors
# used. Default values alongwith min/max/restrictions are listed.
#
# rx_ring_size = 8192; # min 64, max 32768, must be power-of-2.
# jumbo_rx_ring_size = 1024; # min 64, max 4096, must be power-of-2.
# tx_ring_size = 2048; # min 256, max 4096, must be power-of-2.
# max_tx_dma_hdls = 8192; # min 256, max 65536, must be power-of-2.
# # should be no less than tx_ring_size.
#########################################################################
#
# The property below dictates the default max number of receive rings.
# 8 for 83xx.
#
# max_sds_rings = 4; # min 1, max 8, must be power-of-2.
#
#########################################################################
#
# The property below dictates the number of transmit rings.
#
# max_tx_rings = 4; # min 1, max 8, must be power-of-2.
#
#########################################################################
#
# The property below dictates the size of status ring.
#
# max_status_ring_size = 2048; # max 4096, must be power-of-2.
#
#########################################################################
#
# The properties below represents the bcopy threshold for Transmit and
# Receive Frame size. Higher than this threshold gets Mapped.
#
# tx_bcopy_threshold = 128;
# rx_bcopy_threshold = 128;
#
#########################################################################
#
# MTU is the Maximum Transmission Unit(payload without the ethernet header).
# The properties below represents the maximum mtu supported by qlcnic device.
# Use this to enable jumbo frame support. Allowed mtu is 1500 and 9000.
#
# default_mtu = 1500;
#
#########################################################################
#
# The property below dictates whether the driver emits informational
# messages at card initialization time (useful for debugging). Can be
# set to 1 to make driver verbose.
#
# verbose_driver = 0;
#
#########################################################################
#
# The property below dictates whether the driver should enable Large Send
# Offload.
# Enable LSO : 1
# Disable LSO : 0
# Default : 1
#
# lso_enable = 1;
#########################################################################
#
# The property below dictates when the driver should recycle tx
# descriptors
#
# tx_recycle_threshold = 256;
#########################################################################
#
# intr_coalesce_rx_time_us = 1;
# intr_coalesce_rx_pkts = 64;
# intr_coalesce_tx_time_us = 4;
# intr_coalesce_tx_pkts =64;
#########################################################################
#
# The property below dictates whether the driver should enable
# extended logging. Default - disable.
#
# extended-logging = 0;
#########################################################################
#
# disable_fw_minidump = 1;
#
# The property below dictates the size of mindump captured (if enabled)
# Valid range: 0xf to 0xff
#
# md_capture_mask = 0x1f;
#########################################################################
# The property below dictates whether the driver should enable Large
# receive offload (LRO).
# Enable LRO : 1
# Disable LRO : 0
# Default : 1
#
# enable_lro = 1;
#########################################################################
#
# The properties below are related to multicast
#
# multicast_list_max_size = 1024; #size of driver mcast list buffer
# multicast_list_hw_max_size = 16; #how many mcast address can be added
# #to hardware
#########################################################################
# mrrs=2; # Max Read Request Size, Valid values are 0,1,2,3
# If this value is > 3 or not set, the driver will NOT program
# anything to the firmware
#########################################################################
# enable_multi_rds_sets = 1; # Enable = 1, Disable = 0.
#########################################################################