Current File : //kernel/drv/qlt.conf

#
# Copyright (c) 2008, 2012, Oracle and/or its affiliates. All rights reserved.
# Use is subject to license terms.
#
# Copyright 2012 QLogic Corporation.  All rights reserved.
# Use is subject to license terms.


ddi-forceattach=1;

#Name:  PCI max read request override
#Type:  Integer, bytes; Range: 128, 256, 512, 1024, 2048, 4096
#Usage: This field specifies the value to be used for the PCI max read
#       request setting, overriding the default value or the value programmed
#       by the system.
#NOTE:  The minimum value is 128 bytes on PCI Express and 512 on PCI; if
#       this variable does not exist or is not equal to 128, 256, 512, 
#       1024, 2048 or 4096, the ISP2xxx uses the default or the value
#       specified by the system.
pci-max-read-request=2048;

#Name:  PCI max payload override
#Type:  Integer, bytes; Range: 128, 256, 512, 1024
#Usage: This field specifies the value to be used for the PCI max payload
#       setting, overriding the default value or the value programmed
#       by the system.
#NOTE:  This variable only works on PCIe HBAs.
#pcie-max-payload-size=1024;
#

#
# Extended Error Logging capability
#
extended-logging=0;

#
# extended log entries
# default: 256
#
log-entries=4098;

#
# Firmware dump flags
# Usage: These flags are used to force a firmware dump when the flag
# 	 condition occurs.
# default: 0 
# TAKE_FW_DUMP_ON_UNSOL_LOGO  1	 
#
fw-dump-flags=0;

#
# interrupt mode 
# 0: msix
# 1: msi
# 2: lagacy, i.e. fixed interrupt)
# default 0
#
intr-mode=0;

#
# Maximum number of request queues
# default: 2
# max: 256
#
max-reqq-size=2;


#
# Maximum number of response queues
# default: 2
# max: 256
# must be equal to max-reqq-size
# only applicable to Hilda 
#
max-respq-size=2;

#	
# Two modes to determine to which response queue a completed IOCB
# should be directed.
#
# Default: 0 Each request queue can be associated (at creation time) to
#            a response queue.
#          1 Each IOCB can be associated to a response queue. Always use
#            response queue 1 for data transfer phase
#
resp-mode=0;

#
# T10DIF support
#
# default: 0 disabled
#	   1 enabled
#
t10-dif=0;

#
# interrupt handshake
# 0: disabled.
# 1: enabled.
# default 1
# Hidden parameter.
#
intr-hs=0;

#
# This parameter only applies to 16GbFC/FCoE HBA.
# default: 0 Always load fw from fw module first, then from flash if 
#	     fw module are not available.
#	   1 Only load fw from flash on board.
#
load-flash-fw=0;

#
# hilda-wa
# hilda-wa resp in pointer issue workaround.
# Hidden parameter
#
# hilda-wa=1;


#
#Name:  DDI Force Load
#Type:  String List
#Usage: This field declares firmware module paths so that they get
#       loaded early enough to be available for qlc root instance to
#       use.  Correct operation depends on the value of 'ddi-forceload';
#       this value should not be changed by the user.
ddi-forceload = "misc/qlt/qlt_fw_2400", "misc/qlt/qlt_fw_2500", "misc/qlt/qlt_fw_8100", "misc/qlt/qlt_fw_2031", "misc/qlt/qlt_fw_8301";